RC Model Shop

Z2205/34 - Hyperion

This is a higher KV outrunner designed to swing props faster, more for speed than hovering. Perfect for direct drive props up to around the 7x5 size for those models where you want to go fast, but don't want a heavy motor.

On 2S lithiums, you would expect this motor to swing a 7x5 slowfly prop at around 8500RPM.

On 3S lithiums, you would run a 6x4E prop at around 13,500RPM

Super light, super durable and super efficient, this little motor has a lot more power than it's size indicates.

Price $79.00

Z2205/38 - Hyperion

This motor is the perfect small motor for those 3D type planes. It will run well on 2 lithium cells swinging an 8x4.3 slowfly prop.

It is also a great motor for those small electric gliders as it will swing a 6x3 folding prop at 12,500RPM on a 3 cell lithium battery.

Plus it works for those small park flyers as it will swing an APC 6x4E prop at over 13,000RPM on 3 lithiums. That'll get your 600g parkflyer howling!

I have used this motor to hover models weighing 280g with ease. Don't be shy to use this motor on bigger models than its tiny size suggests.

Price $79.00

Z2205/46 - Hyperion

This little motor will swing a big prop for its size. It has a huge torque rating and would be best suited for a slow flyer that needs lots of vertical pull.

This motor is intended specifically for 3-Cell E3D with GWS 8x4DD (aka HD) prop, or Two-cell E3D with APC 9x3.8 or GWS 9x4.7. You can see that it would also make a super sport motor, turning the GWS 7x3.5DD at nearly 12,000 rpm on only 52 watts!! Max recommended continuous currrent is 6A, with short-time peak at 7.5A. Do not run Slowfly type props on 3S.

Price $79.00

Z2209/26 - Hyperion

This is a lovely parkflyer motor on 3 lithiums swinging an 8x6 prop. Being a hotter wind than its 3D brother, it swings props faster, giving us more speed which suits parkflyers better.

Perfect in the GWS warbirds or similar parkflyers weighing up to 600g. It will swing an 8x6 at around 8500RPM on 3 lithiums.

Price $89.00

Z2209/30 with Variable Pitch System - Hyperion

Special Z2209 30-Turn Motor with Pre-installed Variable Pitch System. 5mm hollow Main Shaft with double bearings for smoothest action and high efficiency.

The Hyperion Variable Pitch System uses a special 30-Turn winding of Z2209 Outrunner motor. Most VP systems on the market use 30g, 5mm stator motor to save 10 grams of weight, but this results in low efficiency at high current levels, and limits the systems to models of 200g or less for adequate performance. We've chosen the 2209 to allow ballistic performance for "ShockFlyer" class models of 180~230g, and ability to drive models as heavy as 320g with power still in reserve.

VP Systems require radios which can mix throttle channel.

Price $124.00

Z2209/32 - Hyperion

Probably the closest motor in the range to the famous AXI 2208/34. If you want a something different to replace the undisputed motor that has revolutionised 3D flying, the AXI 2208/34, then this is it. I've spent a long time looking for something with the quality of the AXI, and the Hyperion motors more than fit the bill.

This motor is perfect for the Joker, Frakar, Extra 3D running a 10x4.7 and even powers the GWS warbirds very well on an 8x6 prop.

Price $89.00

Z2213/20 - Hyperion

This is a grunty outrunner designed for bigger models over 400g. You would need to run a 1050 Tanic pack to cope with the current draw of this motor, but be prepaired to be astounded by the power that this tiny motor produces.

It is very happy on 2 lithiums and will hover most parkflyers with ease. I use one on a 365g model and it hovers it with ease on 2S lithiums and a 11x4.7 slowfly prop.

Price $95.00

Z2213/24 - Hyperion

A beautiful 3S lithium motor to 3D those heavy planes weighing up to the 600g mark. This motor has HUGE thrust for its wieght. Put an 11x4.7 slowfly prop on and this motor will drag just about anything up.

Price $95.00

Z3007/26 - Hyperion

This little powerhouse is designed for more speed and smaller props. It will go in everything from a 1.5m glider/hotliner to a warbird swinging around a 9x5E size prop at speed. But just check out the weight. It is the same weight as a standard Speed 400 can motor!!!

Expect to swing a 9x5E prop at 9500RPM on 3 cell lithiums.

Price $109.00

Z3007/30 - Hyperion

This ultra light, beautifully made outrunner is designed to swing a big prop in scale or 3D type projects. It's huge strength is the motors lack of weight compared to the power that it produces. A fantastic motor for models up to 2kg as this motor will produce around 1.4~1.5KG of static thrust on 3 lithiums.

Swings a 12x6E prop at 6600RPM on 3 cell lithiums.

Price $109.00

Z3013/14 - Hyperion

Reliable, powerful, beautifully-made motors with tapered nose to fit in places an OutRunner never fit before. Not only the most reliable large OutRunners ever made, but also the most efficient, at up to 85% on direct drive!

This motor will swing a 10x5E prop at approx. 9000RPM on 3S lithiums at around 22Amps.

Price $120.00

Z3013/16 - Hyperion

Reliable, powerful, beautifully-made motors with tapered nose to fit in places an OutRunner never fit before. Not only the most reliable large OutRunners ever made, but also the most efficient, at up to 85% on direct drive!

This motor will swing a 12x6E prop at approx. 7400RPM on 3S lithiums at around 30Amps.

Price $120.00

Z3019/10 - Hyperion

Reliable, powerful, beautifully-made motors with tapered nose to fit in places an OutRunner never fit before. Not only the most reliable large OutRunners ever made, but also the most efficient, at up to 85% on direct drive!

This motor is very similar to the AXI 2820/10 with very comparable thrust and current draw figures.

This motor will swing a 12x6E prop at approx. 8200RPM on 3S lithiums at around 40Amps.

Price $130.00

Z3025/06- Hyperion

The Z3025-06 is specifically intended for 7-Cell LMR glider competition (or 2S Lithium sport glider use). Props 12x6 to 15x10 may be used, depending on whether you are in competition, or just having fun. Performance is rather astounding - matching Hacker B40 6L +4.4:1 Maxon gearbox motors in efficiency of about 80% at 70A, while weighing nearly 40 grams less and costing about 40% of the price. Very nice in 1.4~1.6M Hotliners with 11x8 prop on 7~9 cells, too.

The Z3025-06 can also do duty in an IC engine 25-Class to 40-Class models with 3S lithium and APC SPORT 9x5 to 10x5 props. We do not recommend "E" props for this motor on 3S lithium. Battery should be rated for 38 to 45A continuous depending on prop.

Price $140.00

Z3025/08- Hyperion

Reliable, powerful, beautifully-made motors with tapered nose to fit in places an OutRunner never fit before. Not only the most reliable large OutRunners ever made, but also the most efficient, at up to 85% on direct drive!

The Z3025-08 is excellent as motor for sport gliders 2~2.5M on 7~9 cells with props 12"~14". Choose prop/battery to achieve 50A or less if runtimes will exceed 20 seconds.

On 3S lithium rated for about 40A continuous or higher, the Z3025-08 is a superb motor for sport models from about 1Kg to 2.5Kg, depending on type. In the Hyperion P-51 Mustang 25, which weighs about 1.5Kg with retracts and scale spinner, the motor provides exciting speed and very strong climbs at only 327W on APC "E" 10x7 prop. With the 10x10 APC "E", it is 'blazing' fast.....

Max prop size on 3S for an E3D models should be 13x6.5 E. For 4S, limit prop to APC SPORT 11x4 maximum (do not use "E" prop on 4S).

This motor will swing a 12x6E prop at approx. 8300RPM on 3S lithiums at around 40Amps.

Price $140.00

Z3025/10- Hyperion

Reliable, powerful, beautifully-made motors with tapered nose to fit in places an OutRunner never fit before. Not only the most reliable large OutRunners ever made, but also the most efficient, at up to 85% on direct drive!

The Z3025-10 is primarily intended for thermal gliders using large folding props, for E3D models on 3S, and sport models on 3S or 4S lithium.

This motor will swing a 14x7E prop at approx. 6300RPM on 3S lithiums at around 35Amps. I've used this motor in both a 1.5kg 3D model on 4S lithiums and a 14x7E prop for impressive hovering and climbout, and a 2m composite glider on 10 x NiMH cells swinging a 14x9 folder which gave me way more power than expected. The glider climbs and accelerates vertically getting you very high, very fast. Static current draw however was only 37Amps!

Price $140.00

Z4025/10 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $189.00

Z4025/12 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $189.00

Z4035/10 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $209.00

Z4035/12 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $209.00

Z4045/10 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $229.00

Z4045/12 - Hyperion

Hyperion Z4025 Outrunner Motor Series for Large Electric Models and IC Engine Conversions

NEW! HYPERION Z4025 Series Brushless OutRunner Motors. Stator measures 40mm Dia x 25mm Length. Extremely powerful, yet reliable and smooth due to the support of large ring bearing at bell front. Z4025 Series is intended for Large Electric models and IC Engine conversions in the range of Glow 40 to Four-Cycle 70, using 4S to 6S lithium typically, or up to 8S with Z4025 16T version. We prefer to use 3200 to 3700mAh 15C~20C batteries in the range of 30A to 60A, and increase cell count if more watts in are needed. This not only increases motor efficiency, it keeps the battery simple (no parallel connections) and reduces project cost.

Price $229

Y22L-2840 - Hyperion

The new Y-Series Hyperion 2-pole, high-rpm motors have it all; they are specifically designed to virtually drop-in replace "Speed 300" Mabuchi 370 motors. Motor diameter, mount spacing and screw size match S300 for perfect fit in GWS and other "300" class gearboxes, GWS EDF-55/64, WemoTec Micro, and Alpha Models Ducted Fans.

From front to back, only the highest quality materials and components are used. For example, the high-speed, shielded stainless bearings in the Z Series are made by NMB Japan; expensive for Hyperion to install, but well worth it for smoothness and longevity.

Price $85.00

Y22L-3000 - Hyperion

Price $85.00

YH22XL-3280 - Hyperion

Price $85.00

YH22XL-3600 - Hyperion

The new Y-Series Hyperion 2-pole, high-rpm motors have it all; they are specifically designed to virtually drop-in replace "Speed 300" Mabuchi 370 motors. Motor diameter, mount spacing and screw size match S300 for perfect fit in GWS and other "300" class gearboxes, GWS EDF-55/64, WemoTec Micro, and Alpha Models Ducted Fans. Bearing boss is 9mm to fit in tight spaces, but includes 10mm spacer to secure the motor in 400-class gearboxes as well.
From front to back, only the highest quality materials and components are used. For example, the high-speed, shielded stainless bearings in the Z Series are made by NMB Japan; expensive for Hyperion to install, but well worth it for smoothness and longevity.

Price $85.00

YH22XL-3900 - Hyperion

Thsis motor is a perfect upgrade motor for the T-Rex Heli.

Price $89.00

Hyperion Motors - Overview

RC Bandit is excited to present to NZ the range of HYPERION brushless motors, speed controllers, receivers, battery chargers, accessories and the EMeter.

HYPERION IS NOW IN STOCK AND CHECK OUT THE AMAZING PRICES!!!!!

The new Z-Series Hyperion Outrunners are some of the best-built motors we have ever seen. From front to back, only the highest quality materials and components are used. The arrangement of twelve stator poles and fourteen magnet poles is primarily responsible for the high torque the Z Series generates on direct drive. But there is much more to the "Z" than that. The stators are hand-wound in an optimal pattern for copper packing, so we get less resistance for a given number of turns. The stator plates are produced via a CNC process that insures uniformity, and made of a new silicon steel with superior permeability at high induction. The stator plates are finished with a lifetime anti-oxidant coating, to eliminate losses which can occur due to magnetic shorting from corrosion.

The magnets are especially made for the Z Series motors, and are rounded on both bell and stator sides. The result it that contact area with the bell is complete, and this has two benefits: First, heat transfer is maximized, so the magnets are much less subject to damage from overheating. Second, the full contact with the bell on one side, and matching curvature to the stator on the other, means that the magnetic flux lines are complete and optimally shaped; this means higher efficiency, lower incidence of motor stalling, and smoother starts.

The magnets themselves are produced in one of the foremost factories in the world, and are the latest type, featuring both an extremely high temperature rating and high magnetic strength. They are retained by fingers in the bell-end, and attached with a special high-temp glue made for the Japanese space program. We think it's just about impossible to throw a magnet, or temperature de-mag these motors, and we've tried very hard...

Finally, the high-speed, shielded stainless bearings in the Z Series are made by NMB Japan; expensive for Hyperion to install, but well worth it for smoothness and longevity. As you'll see in the specifications and prop data, the Z-Series have very high power-to-weight ratios. The Z2209-32 at only 41.7g, for instance, is a tremendous performer on 3S li-po and 10x3.8 APC SF prop in E3D models weighing up to 350 grams.

Warp4 - 2 Turn - RCer

These beautifully made 6 pole brushless motors are the very best quality in-runners around. Designed to direct drive props without the need of a gearbox, these motors allow you to save weight and expense. They are a hi torque brushless motor with almost the same weight and size as a standard Speed400 motor, but with lots more power! Speed400 and Speed480 mounting positions make them an easy upgrade.

This 2 wind model is best suited for ducted fan applications, or you can use it on two lithiums or 7 cell NiMh and a tiny prop in a pylon racer for insane speeds.

Price $135.00

Warp4 - 3 Turn - RCer

These beautifully made 6 pole brushless motors are the very best quality in-runners around. Designed to direct drive props without the need of a gearbox, these motors allow you to save weight and expense. They are a hi torque brushless motor with almost the same weight and size as a standard Speed400 motor, but with lots more power! Speed400 and Speed480 mounting positions make them an easy upgrade.

This 3 wind model is best suited for pylon racer applications or for something that you want to go really really really fast! Run with an APC 4.75x4.75 pylon prop.

I have been flying this motor in a Sokol Pylon racer with a 6x5.5 prop on 3 lithiums and it is seriously fast. Full throttle can only be held for a short period or you loose sight on of the plane because its going just that fast!!! Yeah Baby!

Price $135.00

Warp4 - 4 Turn - RCer

These beautifully made 6 pole brushless motors are the very best quality in-runners around. Designed to direct drive props without the need of a gearbox, these motors allow you to save weight and expense. They are a hi torque brushless motor with almost the same weight and size as a standard Speed400 motor, but with lots more power! Speed400 and Speed480 mounting positions make them an easy upgrade.

This 4 wind model is best suited for direct driving an APC 7x5E prop. Perfect for park flyers that you want to really screen and have unlimited vertical. I've got one in my GWS spitfire and it is outstanding on a 3 cell Tanic lithium battery. Re-enforcing the wings is a must for this sort of power! Don't be frightened off as this motor will run beautifully on a 6x4 prop as well, to give you long run times and moderate speeds with awesome climb outs.

Price $135.00

AXI MINI AC1215 EXTREME - Model Motors

The most powerful of the 300 size MiniAC brushless motors with neodym magnets, dural can with cooling fins, unique solder posts for easy wiring and it is supplied with the all dural planetary gearbox, VMGM 6,00:1. The motor is manufactured using modern technology from the finest materials. The motor is especially designed for performance models of 480-600 size up to 1200g in weight. This motor is two pole, high RPM, and is used only with the VMGM planetary gearbox.

Price $230.00

AXI 2208/34 - Model Motors

This is the ultimate 3D motor for planes up to 370grams / 13oz. Run on 2 or 3 cell lithium and a 9x4.7 to 11x4.7 prop. I have tested many brands of outrunner motors of this size and the AXI is hands down the winner. It will take the abuse of indoor flying and has fantastic power for outdoors. There is a reason that it has won so many awards.

Price $119.00

AXI 2212/20 - Model Motors

For those mof you that wanted more grunt for your 400g + parkflyers, here it is.

Price $125.00

AXI 2808/20 - Model Motors

High torque brushless motor with rotating drum and high power neodym magnets suitable for models of 400-500 size, and up to 1500g in weight. Hardened shaft have 4mm diameter and is supported by two ball bearings. Due to it’s high torque this motor is capable of turning large propellers with a high level of efficiency and without the need for a gearbox.High torque brushless motor with rotating drum and high power neodym magnets suitable for models of 400-500 size, and up to 1500g in weight. Hardened shaft have 4mm diameter and is supported by two ball bearings. Due to it’s high torque this motor is capable of turning large propellers with a high level of efficiency and without the need for a gearbox.

Price $139.00

AXI 2820/10 - Model Motors

Brushless motors with neodymium magnets and rotating case are manufactured using advanced technologies from finest materials. Twin ballraced hardened steel shaft and overall robust but lightweight construction ensure very long lifetime.The unique design of the motors gives extremely high torque allowing to rotate large diameter and pitch propellers without need of a gearbox.

Price $159.00

AXI 2820/12 - Model Motors

Brushless motors with neodymium magnets and rotating case are manufactured using advanced technologies from finest materials. Twin ballraced hardened steel shaft and overall robust but lightweight construction ensure very long lifetime.The unique design of the motors gives extremely high torque allowing to rotate large diameter and pitch propellers without need of a gearbox.

Price $159.00

A20-34S - Hacker

A20-S- Developed for 4-8 oz. Indoor Slowflyers and Indoor Aerobatic models with 2 cell LiPoly batteries. The 12 pole “Outrunner” type design creates MASSIVE TORQUE, therefore larger direct drive props can be used without the need for a gearbox. This motor features Oversize bearings, Curved Neo-magnets, and High efficiency stator design.

Included are 2 prop adapters, plywood and aluminum motor mounts, screws and 2 spare shafts. The motor uses a standard 3mm output shaft.

Price $109.00

A20-26M - Hacker

A20-M- Developed for 7-12 oz. Slowflyers and Aerobatic Parkflyers models with 3 cell LiPoly batteries. The 12 pole “Outrunner” type design creates MASSIVE TORQUE, therefore larger direct drive props can be used without the need for a gearbox. This motor features Oversize bearings, Curved Neo-magnets, and High efficiency stator design.

Included are 2 prop adapters, plywood and aluminum motor mounts, screws and 2 spare shafts. The motor uses a standard 3mm output shaft.

Price $119.00

A20-30M - Hacker

A20-M- Developed for 7-12 oz. Slowflyers and Aerobatic Parkflyers models with 3 cell LiPoly batteries. The 12 pole “Outrunner” type design creates MASSIVE TORQUE, therefore larger direct drive props can be used without the need for a gearbox. This motor features Oversize bearings, Curved Neo-magnets, and High efficiency stator design.

Included are 2 prop adapters, plywood and aluminum motor mounts, screws and 2 spare shafts. The motor uses a standard 3mm output shaft.

Price $119.00

A20-20L - Hacker

A20-L- Developed for 12-18 oz. Parkflyer models with 3 cell LiPoly batteries. The 12 pole “Outrunner” type design creates MASSIVE TORQUE, therefore larger direct drive props can be used without the need for a gearbox. This motor features Oversize bearings, Curved Neo-magnets, and High efficiency stator design.

Included are 2 prop adapters, plywood and aluminum motor mounts, screws and 2 spare shafts. The motor uses a standard 3mm output shaft.

Price $129.00

A20-22L - Hacker

A20-L- Developed for 12-18 oz. Parkflyer models with 3 cell LiPoly batteries. The 12 pole “Outrunner” type design creates MASSIVE TORQUE, therefore larger direct drive props can be used without the need for a gearbox. This motor features Oversize bearings, Curved Neo-magnets, and High efficiency stator design.

Included are 2 prop adapters, plywood and aluminum motor mounts, screws and 2 spare shafts. The motor uses a standard 3mm output shaft.

Price $129.00

20/8/16E - HCS

This Czech made outrunner is designed to run the EPP warbirds and similar 200g (7oz) indoor/park models. I am amazed at how effective this little motor is. It is tiny yet has heaps of go. I've been running a 9x4.7 slowfly prop and 3 lithiums on one on a Streetfighter weighing 200g and it hauls it straight up with authority! On 2 cells it still has a lot of go and will happilly fly the streetfighter around the park. The power in this tiny, light motor is impressive.

Using an 8x6 prop on 3 cells this little motor hauls a streetfighter around quickly. It has changed the Streetfighter from a lazy indoor plane to a savage outdoor war bird.

For indoor models up to 230g (8oz) this motor is a perfect 3D motor on 3 lithiums. Perfect for a light Joker or Blitz, this is an inexpensive brushless option.

Price $69.00

34/20/8E - HCS

This outrunner is designed as a 3D motor for a plane weighing up to 1.7kg. It produces 2kg of static thrust on 4S lithiums at 26Amps. Best propellers are 15x4 or 16x4.

The perfect motor for the Blade XL.

Price $175.00